JPC Racing

JPC- Coyote VCT Actuator Block off

When Deleting the VCT on your Coyote Engine 2011-2017 delete the ugly VCT actuators with this Billet 6061 aluminum block off. This is a complete kit that includes 4 block offs enough to do 1 entire...

JPC Racing

JPC- 2011+ GT/Boss Stg. 3 Breather Package

Valve Cover Breathers Eliminates Oil in the intake Cleans up engine bay All Hardware included DO NOT OVER TIGHTEN T

JPC Racing

2011+ GT/Boss Billet One-Way Valve Cover Crankcase Breather Kit

Free up Horsepower - Eliminate Crankcase Pressure Brand new Billet One-Way Crankcase Breather Kit. This is a direct replacement for the factory oil fill cap that vents unwanted crankcase pressure to...

JPC Racing

JPC- 2011-up GT/Boss Stg. 2 Breather Package

Eliminates Oil in the intake Cleans up engine bay All Hardware included     Click Here: 

JPC Racing

JPC- 2011+ GT/Boss Breather Package

Eliminates Oil in the intake Cleans up engine bay All Hardware included   DO NOT OVER TIGHTEN THE CLAMP.  THERE IS NO WARRANTY IF RUBBER IS CUT IN CLAMP AREA   

ARP

ARP- Coyote Balancer Bolt

As the crankshaft flexes, the damper absorbs incredible amounts of energy. These damper bolt kits from ARP will ensure that your balancer is locked into position. They feature a 1/4 in. thick...

ARP

ARP- PRO Series Modular Flywheel Bolt Kit Set of 8

ARP Pro Series Flywheel Bolts Pro Series flywheel bolts from ARP give you all that you need to bolt in your flywheel with confidence. They're much stronger than OEM hardware, forged from aerospace...

JPC Racing - Coyote Engine secondary Flip Kit (11-17)

With the Use of this tensioner flip kit,  we are able to flip the tensioner on the Left head.  One of the coyotes design flaws is the fact that the tensioner, tensions the drive side of the chain,...

JPC Racing Cam Sensor Block Off Kit (Each)

Block off your factory cam sensors with these Delete plugs.  Perfect use when switching to a stand alone ECU      Off Road Use only. 

JPC Racing Coyote water pump Heater Fitting (AN Conversion)

JPC Racing Heater Fitting made of 6061 Billet Aluminum , Finished in Anodized Black. This item is great for those wanting to switch their Heating lines to the AN style fitting.  Made In...

Cometic- MLS 5.0 Gen 2 Coyote Head Gaskets ( Right) .051

Same Gaskets Used on all JPC in house builds!   The Cometic MLS gasket is comprised of three layers of Stainless Steel. Cometic uses Stainless steel for increased strength, its ability to rebound and...

Cometic- MLS 5.0 Gen 2 Coyote Head Gaskets ( Right) .040

Same Gaskets Used on all JPC in house builds!   The Cometic MLS gasket is comprised of three layers of Stainless Steel. Cometic uses Stainless steel for increased strength, its ability to rebound and...

Cometic- MLS 5.0 Gen 2 Coyote Head Gaskets ( LEFT ) .040

Same Gaskets Used on all JPC in house builds!   The Cometic MLS gasket is comprised of three layers of Stainless Steel. Cometic uses Stainless steel for increased strength, its ability to rebound and...

2011-2019 FORD 5.0L COYOTE BILLET PISTON SQUIRTER BLOCK OFF KIT

These Billet Aluminum oil squirter block offs are simple to install and are oringed to prevent any pressure loss. Sold as a kit only they containing a set of four block offs. They eliminate the...

Clevite - Gen1 & Gen2 Coated H-Series Main Bearings

Clevite coated H-Series main bearings were developed primarily for NASCAR racing, but are also well-suited to other types of competition engines. They are especially good for engines that run at...

JPC Billet Oil Squirter Delete Plugs (2011-2019 Coyote Engine) set of 4

  6061 Material Lightweight  Built in the USA  Now available for all coyote blocks from 2011-2019 these oil squirter plugs allow for the remove

ARP

ARP- Coyote cam phaser to cam shaft bolt kit (set of 12)

End your camshaft timing worries with ARP Pro Series cam bolt kits! Featuring 200,000 psi tensile strength, these kits deliver increased preload clamping force and ensure positive timing gear...

ARP

ARP- PRO Series Modular Flexplate Bolt Kit Set of 8

These bolts are the recommended part for any Ford Modular 8 bolt crankshaft upgrade or if you want to strengthen your 6 bolt unit these will work also.   These Pro series flywheel bolt kits from ARP...